Calculate drill RPM and feed rate from cutting speed, drill diameter and feed per revolution.
Calculation overview
This tool is built for the part of the job where a few numbers need to be checked before the machine does the work. Drilling looks simple on paper, but the tool is cutting across a changing geometry and has to move chips out through a hole. Diameter, cutting speed and feed per revolution are the main inputs for many basic drill calculations. Calculate drill RPM and feed rate from cutting speed, drill diameter and feed per revolution. The purpose is simple: give you the mathematical relationship in a form that is quick to enter, quick to check and easy to connect with the next calculation.
Use these tools when setting drill RPM and feed, checking a hole cycle, estimating a peck depth, or working through a drill point and straight hole depth calculation. For this drilling tool, the numbers are most useful when you already know the basic job conditions and want a clean calculation instead of doing the arithmetic by hand.
Required inputs and units
Use the unit shown beside each field. These are the values the calculation expects. A unit mismatch is one of the easiest ways to get a technically correct formula with a practically wrong answer.
| Input | Unit |
|---|---|
| Cutting Speed | m/min |
| Tool / Part Diameter | mm |
| Feed per Revolution | mm/rev |
Formula and method
Formula: RPM = (1000 × cutting speed) ÷ (π × drill diameter). Feed rate = RPM × feed per revolution.
The calculator links the drill diameter to spindle RPM, then uses feed per revolution to calculate the linear drill feed. Use the drill manufacturer’s cutting data as the primary reference. The result is calculated from the values you enter. Nothing is inferred from a material catalogue or a machine database unless the page explicitly says so.
Using the result
Start with reliable inputs. Check the drawing, tool data, machine control values and the unit beside each number. Enter the values, calculate the result and read the output with the unit attached. Where the tool gives more than one result, treat them as a set because changing one input can change the relationship between the outputs.
- Confirm that the entered dimensions match the physical tool, workpiece or operation.
- Keep the unit system consistent from input to result. Use a converter before mixing inch and metric data.
- Compare the calculated value with the cutting data supplied for the actual cutter or insert.
- Check the result against the machine spindle, feed and control limits before running the operation.
Result interpretation
The result is not automatically a production recommendation. It is the mathematical answer to the relationship shown on this page. That distinction matters in machining because two jobs can use the same calculation and still need different settings. Tool geometry, engagement, workholding, machine rigidity, material condition, coolant and the toolpath can all change the useful operating range.
| Result | Unit |
|---|---|
| Spindle Speed | RPM |
| Feed Rate | mm/min |
Checks before production
Drill type, point geometry, material, hole depth, coolant delivery, chip evacuation, machine rigidity, spindle limits and the required hole size should be checked before production. Deep holes need more process planning than a basic formula can provide. The calculator is intentionally transparent about this. A calculated value is useful when it is checked against the real process. Keep the drawing, tooling data and machine limits beside the result.
For example, a feed calculation can be mathematically correct while the cutter maker recommends a different chip load for the specific material. A turning RPM can be correct for one diameter and wrong after the diameter changes. A tap drill relationship can be correct as a basic calculation but still need a standard specific hole size. The same principle applies to geometry, cost and material calculations: verify what the number represents before applying it.
Example calculation
For example, 25 m/min with a 10 mm drill and 0.12 mm/rev gives about 796 RPM and 95.5 mm/min feed.
Related calculators
- Drill RPM Calculator (Calculate drill spindle speed from cutting speed and drill diameter.)
- Hole Depth Calculator (Calculate effective hole depth from total programmed depth and point allowance.)
- Peck Drilling Calculator (Calculate a simple peck depth from drill diameter and selected multiplier.)
- Drill Feed Calculator (Calculate drill feed rate from RPM and feed per revolution.)
You can also return to the Drilling calculator category or open the full calculator library to continue the calculation sequence.
Related resources
- Material reference for common material notes and density information.
- Machining reference for formulas, tables and unit conversions.
- Machining guides for practical explanations behind the calculations.
FAQs
Is the Drill Feed & Speed Calculator result ready to use in production?
No. The result is a mathematical starting point. Check the actual tool maker data, workpiece material, machine capability, workholding and job requirements before production.
Why do units matter on this calculator?
The formula is only correct when the input units match the relationship shown. Read the unit beside each field and use the converter tools when you need to move between systems.
What should I do when the drilling value looks too high or too low?
First check the units and the basic inputs. Then compare the result with the current tooling or engineering reference for the job. If the arithmetic is correct, the difference may come from the process rather than the formula.